{ "numMessagesInTopic": 10, "nextInTime": 555, "senderId": "jh3f2yosc8cRArENLY8BQCW2vjG8IhTW9HvXlM3bn_GBS9-2tTjqdFugKfQuH5-hh0yvr17W1lD_p6tobiDHuZ5lUfLZPB0SkyMAiyNh", "systemMessage": false, "subject": "Re: How do I make this 5.1 Surround config work", "from": ""bingalls1947" <bingalls1947@...>", "authorName": "bingalls1947", "msgSnippet": "Thanks again for your input....this really makes sense. Just to continue, then. Once I ve monitored and recorded the input to my MAC, if I want to use some", "msgId": 554, "profile": "bingalls1947", "topicId": 546, "spamInfo": { "reason": "0", "isSpam": false }, "replyTo": "LIST", "userId": 159793802, "messageBody": "
>than
\n> ----- Original Message -----
\n> From: "bingalls1947" <bingalls1947@y...>
\n> To: <01v96@yahoogroups.com>
\n> Sent: Saturday, September 13, 2003 2:49 PM
\n> Subject: [01v96] Re: How do I make this 5.1 Surround config work
\n>
\n>
\n> > Ronny.....thanks for your reply and welcoming me to the group. I
\n> > look forward to many years of great 01V96 mixing.
\n> >
\n> > Just a clarification question. You stated:
\n> >
\n> > >If you want to go 96k and mix 5.1 in your explained intention,
\n
> > >you may want to use the MY16-AT and have 12-96k outs, 6 going toin
\n> > >your 5.1 recorder and 6 going to your surround speakers.
\n> >
\n> > I own the my16AT so I'm going to stick with it. The question is
\n
> > this setting I assume you would be monitoring your input sources(
\n
> > as opposed to signals returning from the MAC) since they would befor example if you use the v96 to
\n> > routed to Buses 1-6 that would feed both the recorder and the
\n> > speakers. If you used the other option:
\n> >
\n>
\n> Yes, in this scenario you are just monitoring before the recorder,
\n
> monitor post recorder from Mac. You are feeding your signals tothe Mac and back in the V to
\n
> monitor, monitoring from the board and not post recorder back tothe V, will allow you to mix to the
\n
> 6 recorder tracks and eliminating any possiblitly of feedbackloops. No problem doing it either way,
\n
> but you'll still have to separate the post recorder sendsmonitoring, from the 6 sends going to
\n
> recorder.from
\n>
\n> > >In regard to your question of whether it's ok to use the analog
\n> > >outs for monitoring 5.1 mixing in conjunction with the ADAT 4 at
\n> > >96k. Yes, it's perfectly ok, as the DAC's are very good and you
\n> > >have to turn it to analog at some time to hear it anyway.
\n> >
\n> > even if you configured this system with 12 channels coming back
\n
> > the MAC you only have 2 busses and possible the stereo bus leftto
\n
> > route them to...so is there any way to monitor those signals in5.1
\n
> > surround using the standard 2 Stereo Outs (Front L&R) and 4 Omnibeing
\n> > Outs (Rear L&R, Center & sub)?
\n> >
\n> > The same question also pertains to a 48K setup. With 6 busses
\n
> > used for recording if you pass a monitor signal back to yourmixer
\n
> > how do you monitor it in 5.1 surround?out's. Yes that's possible. However
\n> >
\n>
\n> I assume that by Front L&R stereo outs that you mean the 2TR rca
\n
> by using the stereo XLR outs and the omni's, it will give 6balanced +4dBu outs going to all 5
\n
> monitors and the LFE sub, instead of the two unbalanced -10dBVsensitivity outputs that are on the
\n
> 2TR outs and the 4 +4dB balanced omni's. IOW, you are mix andmatching output sensitivity and
\n
> balanced and unbalanced sends with your setup. You can monitoryour six channels this way, but the
\n
> v96 doesn't have a surround encoder, only surround matrix. Theencoding to 2 track would have to be
\n
> done with DVD authoring on your Mac or PC. So the config that I'mtalking about is monitoring 6
\n
> channels to 6 separate monitors before any encoding is performed.This allows you to mix let's say
\n
> 24 tracks, down to 6, using the 5.1 surround mode with rotationalpans, while monitoring your 6
\n
> surround channels going to 6 tracks on recorder, with you in themiddle of the surround monitors. By
\n
> using the busses in 5.1 surround mode, you'll be able to use thevirtual joystick on each channel to
\n
> set and assign the pan trajectory X-Y axis to each of the 6 masterbusses that you'll be using to
\n
> the speakers.http://docs.yahoo.com/info/terms/
\n>
\n>
\n>
\n> > Thanks again for your help
\n> >
\n>
\n> My pleasure.
\n>
\n> Keep On Trackin'
\n>
\n> Ronny Morris - Digitak Mastering
\n> http://208.191.230.169/digitak.php
\n> ------Powered By Experience------
\n> --------Driven To Perfection--------
\n>
\n> > Bob
\n> >
\n> >
\n> >
\n> >
\n> >
\n> >
\n> > To unsubscribe from this group, send an email to:
\n> > 01v96-unsubscribe@yahoogroups.com
\n> >
\n> >
\n> >
\n> > Your use of Yahoo! Groups is subject to
\n
> >