{ "numMessagesInTopic": 18, "nextInTime": 2405, "senderId": "jbyMHGJEVTJL6Sd2dkn3B9TAcms1EZdTixmzR-CTzRBV1VFG4koF96Ngszqpm4iYM78fvFfDQ1JJPafqQeqifVefMaItNBCI5MBmMcZCGXNbwnG0", "systemMessage": false, "subject": "Re: can't change ip address", "from": ""erics_overthere" <motorxtreme@...>", "authorName": "erics_overthere", "msgSnippet": "Oops. I hit send too soon. You will either have to get a new IP lease from your SG20 or set the IP address on your Windows box to a static IP within your", "msgId": 2404, "profile": "erics_overthere", "topicId": 2397, "spamInfo": { "reason": "0", "isSpam": false }, "replyTo": "LIST", "userId": 163242626, "messageBody": "
> Can't you get into the machine by using its name instead of its IPto
\n> address?
\n>
\n> Example: http://myserver:8282
\n>
\n>
\n> --- In magnia_sg20@yahoogroups.com, "rem736" <rem736@y...> wrote:
\n> > ok,
\n> >
\n> > so this is the weirdest thing. i disabled NAT and attempted to
\n> change
\n> > the private ip of the sg20. using xx.xx.xx.x (x representing a
\n> single
\n> > digit), i wasn't able to change it. same complaint about the ip
\n> being
\n> > invalid. then i changed 1 set at a time. going from 192.168.1.10
\n
> > xxx.xx.xx.x, it worked every single time. but as soon as ireduced
\n
> > the first set to only two digits, it would complain. so idecided
\n
> topanel
\n> > trick it and use the number zero for the very first digit in the
\n> first
\n> > set. and what you know, it worked. i checked the sg20's lcd
\n
> > for the private ip and it took. however, it took it with thezero
\n
> asthe
\n> > the first digit of the first set. changing the ip on the client
\n> > machine to connect to the sg20, it would always want to lose the
\n> zero
\n> > in front. so now, i can't get into the sg20. i guess i'll use
\n
> > backup disk to start up and over again. funny how it would nottake
\n
> > an ip with two digits in front. anyone knows of anydocumentation
\n
> onas
\n> > this?
\n> >
\n> > <rem736>
\n> >
\n> > --- In magnia_sg20@yahoogroups.com, "rem736" <rem736@y...> wrote:
\n> > > thank you. i'll give it a go. another thing. i don't see
\n> anywhere
\n> > > that you can disable ssid broadcast. if not within the admin
\n> page,
\n> > > can it be done via webmin?
\n> > >
\n> > > <rem736>
\n> > >
\n> > >
\n> > > --- In magnia_sg20@yahoogroups.com, "erics_overthere"
\n> > > <motorxtreme@s...> wrote:
\n> > > > Try disabling NAT first (I gave it the IPs of my D-Link
\n> router),
\n> > > > change yout private IP, then re-enable NAT. It worked for me.
\n> > > >
\n> > > > --- In magnia_sg20@yahoogroups.com, "rem736" <rem736@y...>
\n> wrote:
\n> > > > > hi,
\n> > > > >
\n> > > > > i tried to change the private ip address within the toshiba
\n> admin
\n> > > > > page and it gives me the following error:
\n> > > > >
\n> > > > > "the ip address or subnet mask is invalid"
\n> > > > >
\n> > > > > anyone know what's going on here? i'm using build 2.6 and
\n> would
\n> > > > like
\n> > > > > to assign the sg20 a private ip that's on the same subnet
\n
> my
\n> > > > > primary internet router. in addition, i would also like to
\n> use the
\n> > > > > lan ports on the sg20 as switches only and have my primary
\n> internet
\n> > > > > router assign the ips.
\n> > > > >
\n> > > > > anyone ever tried to to this? any suggestions? thanks.
\n> > > > >
\n> > > > > <rem736>